I SOLD my 1956 F100 Custom Cab project!...

Dearborn Michigan area. . .about 2-miles from Ford World Headquarters. . .right near Greenfield Village!


Truck is SOLD...but I still have ALL these parts left for sale!!!...
PARTS LIST: NOT installed...most NEW in BOXES!...

2nd set of original rear fenders with spare tire cut-out on driver side fender ---almost NO rust

1970 F100 9-INCH rear axle housing with all brackets removed & cleaned up

Ford 9-inch Big (Torino) Bearing Rear Disc Brake Conversion kit. . .. rotors are 5\" x 4 ½\" Ford pattern. . .

Ford Racing Parts # M-4204-F28A, TRAC-LOC Limited Slip, with 1536-steel billet case caps

ALL bearings & gaskets needed to assemble rear pumpkin. . ..

NASCAR Ford 9-inch 3:89 ring and pinion set --- Back-cut gears!. . . from a NASCAR
team down south....was told it has 1 400-mile race on it...looks PERFECT!

New Dutchman 28-spline Street/Strip axles & retainers with bearings.

Extra \"hooded\" Daytona pinion bearing support without races/bearings

1956 Running boards --- need a few repairs

2nd set of \"short\" cab-length running boards. . .I was going to use these to repair the long ones!




Total Cost Involved Inc.
Mustang-II type Independent Front Suspension.
Includes tubular control-arms, 2-inch dropped spindles, disc brakes with 5\\\\\\\" x 4-1/2\\\\\\\" bolt-circle, hose kit, Firestone airbags, and gas shocks, anti-sway bar, power rack-and-pinion set-up, plus frame-boxing plates!



No Limit Engineering Inc.
FATBAR 4-LINK Rear Suspension with Firestone Air Bags and Doetsch Racing Shocks. Includes Panhard Bar. Plus frame-boxing plates!



Art Morrison Enterprises
2\" x 4\" mandrel-bent square steel tubing for NOTCHES. . ...bent the \"hard way\". . .
These are the same size as the OEM frame rails to use as a \"NOTCH\" over the 9-inch rear end.


Accuair
e-Level Air Management Package w/ Touchpad includes:
ride-height sensors, D.O.T. Approved Plumbing Kit, VU4 4-Corner Solenoid Valve Unit,
e-Level Controller w/TouchPad Interface & 20-ft. mini-USB cable provides communication
to the ECU, ALL Plug-n-Play wiring harnesses & power supply kit, includeds 2 Key-Chain Remotes ($200.00 option!), Aluminum moisture trap and inlet filter. EVERY option available!



12-gallon 8-port D.O.T approved air tank for air ride system
Features:
- (8) 1/2\" Ports
- 4 Ports on face, 1 port on top & bottom & 1
on each end
- Red Oxidized Coated Interior to resist Rust
- D.O.T. Approved
- Powder Coated Gloss Black
- Dimensions: 12 1/2\\\" H x 44\\\" L



ALSO AVAILABLE!...NEW IN BOX!!!

Probe Industries +.030\" SRS SERIES Forged Flat-Top Piston Set = $550.00...NEW in BOX! Ford 331/347 c.i. -4.0cc reliefs, p/n 10666-030.

...And. . .

Clevite - Perfect Circle Moly STREET / RACE Ring Set: $110.00...NEW in BOX!
Part #315-0049-030 1/16\" - 1/16\" - 3.0mm




TRI-POWER....................ORIGINAL!

ORIGINAL --- Early 60\'s SMALL BLOCK FORD 260 c.i. V8 Buddy Barr - Holley tri power set up! ---email for price!
...perfect for 260-289-302 c.i. SMALL BLOCK FORD motors!
WITH CORRECT CARBURETORS!...fuel log, oval air cleaner & a vintage MOON fuel block from the 60\'s!

. . .Includes THREE rebuild kits from HOLLEY and 3 CUSTOM-fabricated carburetor
Isolators! (+1.5\" tall)




VINTAGE Set of Small Block Ford Aluminum Cal Custom \"Hawk\" 9-Fin Valve Covers. $175.00



EVERYTHING is BRAND NEW & still in the original box(s) unless otherwise noted!



Check it out...contact me with any questions!

Thanks!...


-